SHARP AR- 5. 01. 2 SERVICE MANUAL Pdf Download. SERVICE MANUAL CODE : 0.
Вы можете прочитать рекомендации в руководстве пользователя, техническом руководстве или руководстве по установке SHARP AR-5012. Необходимо пригласить специалиста из Индикатор Горит сервисного центра SHARP для проведения вызова пост. сервисного.. » Компьютерная техника. » Ремонт и сервис компьютерной техники. Девелопер SHARP AR152/5012 (O) AR152LD. Арт. № Марка Модель Описание Цена Наличие. 165244 Sharp. 165367 Sharp AR -160UH AR160UH NROLi0030QSZZ Сервисный набор 165396 Sharp AR168T Чип б/г AR -122E/153E/157E/ 5012 /5415/M150/M155 382,32р. Цифровой лазерный копир, Инструкция Sharp AR - 5012, PDF, 2302. Цифровой Руководство пользователя, Инструкция Sharp AR-5600, PDF, 1158.
Прочитайте информацию о заправке Sharp AR-121 E, AR-122 E, AR-M150, AR-153 E, AR-M155, AR-156, AR-5012, AR-5415 Инструкции по заправке лазерных картриджей: Для заправки вам понадобится: - совместимый тонер; - плоская отвертка; - остроконечные щипцы (пинцет). Вопрос: Цифровые копиры Sharp AL, AR, ARM: вход в сервис и сброс Вопрос: Sharp AR5012 - сброс счетчиков техобслуживания.
ZAR5. 01. 2/A1. E DIGITAL LASER COPIER/ PRINTER AR- 5. AR- 5. 01. 2 MODEL CONTENTS [ 1 ] GENERAL ..... SPECIFICATIONS. CAUTION This product is a class 1 laser product that complies with 2. CFR 1. 04. 0 of the CDRH standard and IEC8.
This means that this machine does not produce hazardous laser radiation. The use of controls, adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. At the production line, the output power Caution of the scanner unit is adjusted to 0. This product contains a low power laser MILLI- WATT PLUS 2. PCTS and is device. To ensure continued safety do not maintained constant by the operation of remove any cover or attempt to gain access the Automatic Power Control (APC). CONTENTS GENERAL DISASSEMBLY AND ASSEMBLY 1.
Major functions .... Scan Once Print Many function (Many copies are made by one scan.) Duplex: Auto duplex copy function Memory: Standard page memory FAX: FAX function.
Descriptions of table Standard provision No function or no option available Opt: Option ∗ AL- 1. PKM ∗ AR- PG2 AR- 5.
AR- 5. 01. 2 GENERAL 1 - 1.. Vrms (Min) Power consumption 9. W (Max) Output data R, G, B 1 or 8 bits/pixel / A/D 1.
Writing Writing system Writing to OPC drum by the semiconductor laser section Laser unit Resolution 6. AR- 5. 01. 2 SPECIFICATIONS 2 - 1.. Less than 1. 00. 0W Average AR- 5.
Wh/H *1) (during copying) Average (stand- by) 8. Wh/H *1) Pre- heat mode 1. Wh/H *1) Auto power shut- off mode 4. Wh/H *1) *1) May fluctuate due to environmental conditions and the input voltage. AR- 5. 01. 2 SPECIFICATIONS 2 - 2.. Enlarge: 2mm or less (OC) / 3mm or less (SPF/R- SPF/Duplex) Reduction (5. OC) / 8mm or less (SPF/R- SPF/ Duplex) Warm- up time 0 sec.
Power save mode reset time 0 sec. Paper jam recovery time 0 sec.
AR- 5. 01. 2 SPECIFICATIONS 2 - 3..(1 - 9 = Jan. Sep. 0 = Oct. X = Nov. Y = Dec.) Serial number of month Fixed to 1. Pack division (See table below) End digit of year Version No.
C 4. 5˚C AR- 5. 01. CONSUMABLE PARTS 3 - 1..∗1 The production control label is not attached to the cartridge of a China product.
Developer> Note: Never carry exposed Toner unit. Be sure to put it in the collection bag. Sub lot Production day Production month End digit of year Production place AR- 5. CONSUMABLE PARTS 3 - 2.. Paper output tray Paper output tray extension Power switch Handle Power cord socket — — 2. Internal Fusing unit release lever Transfer charger Toner cartridge Charger cleaner Photoconductive drum — — AR- 5.
EXTERNAL VIEWS AND INTERNAL STRUCTURES 4 - 1..• Copying is possible when the indicator is on. Use to set a user program. Press and hold down during standby to display the total number of • Press to start copying copies made to date. AR- 5. 01. 2 EXTERNAL VIEWS AND INTERNAL STRUCTURES 4 - 2.. Drives the optical mirror base (scanner unit). Toner motor Supplies toner.
Cooling fan motor Cools the optical section. Resist roller solenoid Resist roller rotation control solenoid Paper feed solenoid CPFS1 Cassette Paper feed solenoid 1 AR- 5.
EXTERNAL VIEWS AND INTERNAL STRUCTURES 4 - 3.. PPD1 sensor PPD1 Transmission sensor Paper transport detection 1 "L" at paper pass Door switch Micro- switch Door open/close detection 1 or 0. V of 2. 4V at door open (safety switch for 2. V) AR- 5. 01. 2 EXTERNAL VIEWS AND INTERNAL STRUCTURES 4 - 4.. AC power input, DC voltage control, High voltage control CCD sensor PWB For image scanning LSU motor PWB For polygon motor drive TCS PWB For toner sensor control LSU PWB For laser control AR- 5.
EXTERNAL VIEWS AND INTERNAL STRUCTURES 4 - 5.. Transport the paper from the manual paper feed port. PS roller unit Takes synchronization between the lead edge and the rear edge of the paper.
Paper feed roller Picks up a sheet of paper from the cassette. AR- 5. 01. 2 EXTERNAL VIEWS AND INTERNAL STRUCTURES 4 - 6.. Also make certain the outlet is properly grounded. Be sure to allow the required space around the machine for servicing and proper ventilation. Drum cartridge 2. AR- 5. 01. 2 UNPACKING AND INSTALLATION 5 - 1..
Shake the aluminum bag to stir developer 1. Supply developer from the aluminum bag to the top of the MX roller evenly. Note: Be careful not to splash developer outside Developer unit. AR- 5. 01. 2 UNPACKING AND INSTALLATION 5 - 2..
Pull out the shutter in the arrow direction. Note: Do not hold and carry the shutter. Otherwise the shutter may drop and Toner unit may drop. Completion of Toner unit installation Close the front and side cabinets. AR- 5. 01. 2 UNPACKING AND INSTALLATION 5 - 3.. Note: After loading copy paper, to cancel the blinking "H" without restarting copying, press the clear ( ) key.
The "P" in the display will go out and the ready ( ) indicator will light up. AR- 5. 01. 2 UNPACKING AND INSTALLATION 5 - 4.. Waste toner box To face Synchronization Paper release Fusing Transfer Manual feed Separation with drum down tray Heat roller Electrode Transfer charger Cassette paper feed Transfer high Heater lamp voltage unit Print process Paper transport route AR- 5. COPY PROCESS 6 - 1..
A uniform negative charge is applied over the OPC drum surface by Aluminum the main charging unit. Stable potential is maintained by means of the layer Scorotron charger. Non- image area Image area Positive charges are generated in the aluminum layer. About DC5. 5. KV ( 5. V/ 3. 90. V) AR- 5. COPY PROCESS 6 - 2..
Toner remaining on the drum is removed and collected by the cleaning blade. It is transported to the waste toner collecting section in the cleaning unit by the waste toner transport roller. Toner is attracted over the shadowed area because of the developing bias.
AR- 5. 01. 2 COPY PROCESS 6 - 3.. Voltage added to the screen grid can be selected, high and low. To make it easily understood, the figure below shows voltage transition at the developer unit. START STOP Print potential Toner attract Developing bias potential Drum potential High Time AR- 5.
COPY PROCESS 6 - 4.. The LSU emits laser beams according to the print data. Electrical signals are converted into photo signals.) 6) The laser beams are radiated through the polygon mirror and various lenses to the OPC drum. AR- 5. 01. 2 OPERATIONAL DESCRIPTIONS 7 - 1.. Scanner motor Pulley gear Idle pulley Belt 4. Belt 1. 90 Optical unit Shaft Idle gear AR- 5.
OPERATIONAL DESCRIPTIONS 7 - 2..≠ b ≠ c d = e = f A. General description General block diagram (cross section) f θ LENS Thermal fuse Separator pawl PPD2 Thermistor Pressure roller Heat roller Paper guide AR- 5. OPERATIONAL DESCRIPTIONS 7 - 3.. AR- 5. 01. 2 OPERATIONAL DESCRIPTIONS 7 - 4.. Thus the paper is transported by the resist roller.
After the resist roller starts rotating, the paper is passed through the pre- transfer guide to the transfer section. Images are AR- 5. OPERATIONAL DESCRIPTIONS 7 - 5..
POD jam POD does not turn on within 2. POD does not turn off within 1. PPD2. MPFS AR- 5. OPERATIONAL DESCRIPTIONS 7 - 6..• If there is no damage, execute the procedure of item 1. Part name Ref. 4) Remove the main charger. Drum (Cleaning the screen grid and the sawteeth.) Transfer charger unit Charger wire B.
Drum replacement 1) Remove the drum cover. Lock Tabs) AR- 5.
DISASSEMBLY AND ASSEMBLY 8 - 1.. Attach the drum from (b). Prevention against the sub blade edge moquette to cover the sub blade. Example of NG Attach the drum so that its position with the sub blade is as shown.
AR- 5. 01. 2 DISASSEMBLY AND ASSEMBLY 8 - 2.. Press the side cover open/close button and open the side cover. Transfer charger Lock pawl front D. Assembly procedure For assembly, reverse the disassembly procedure. E. Charger wire cleaning 1) Remove the charger cleaner from the manual paper feed unit. AR- 5. 01. 2 DISASSEMBLY AND ASSEMBLY 8 - 3..• The rest of the charger wire must be within 1. Refer to Fig. 1 • The spring hook section (charger wire winding section) must be in the range of the projection section.
Be careful not to twist the charger wire. Charger wire Protrusion 1. Fig. 1 AR- 5. 01. DISASSEMBLY AND ASSEMBLY 8 - 4.. For assembly, reverse the disassembly procedure 3.
Optical section A. List Part name Ref.
Copy lamp unit Copy lamp Lens unit B. Disassembly procedure 1) Remove four screws, and remove the rear cabinet and the rear cabinet cover. AR- 5. 01. 2 DISASSEMBLY AND ASSEMBLY 8 - 5..
Lift the rear side of the carriage, remove the belt and the connec- tor, and remove the carriage. Note: Attach the FFC to fit with the marking line. Marking line AR- 5. DISASSEMBLY AND ASSEMBLY 8 - 6..
Remove the screw and remove the PPD2 sensor. Cut the binding band, remove the screw, and remove the ther- mistor. PPD2 sensor Thermistor AR- 5. DISASSEMBLY AND ASSEMBLY 8 - 7.. Remove the spring and remove the separation pawls (3 pcs.). Heat roller disassembly (Continued from procedure (4).) 5) Remove screws, remove the fusing cover, and open the heat roller section.
Remove the E- ring and remove the reverse gate. AR- 5. 01. 2 DISASSEMBLY AND ASSEMBLY 8 - 8.. Note: Apply grease to the sections specified with *. Remove two screws and remove the thermo unit. Remove each connector and three screws, and remove the MCU PWB. C. Assembly procedure For assembly, reverse the disassembly procedure. AR- 5. 01. 2 DISASSEMBLY AND ASSEMBLY 8 - 9..
Remove two springs and open the intermediate frame unit. PPD2). 6) Remove two screws and remove the toner motor. Remove the pulleys on the both sides and remove the paper exit roller. AR- 5. 01. 2 DISASSEMBLY AND ASSEMBLY 8 - 1. Pull out the paper exit roller knob and remove the belt. Remove the paper exit roller. Remove the harness guide.
Release the belt pulley (a) lock and remove the belt pulley bearing. AR- 5. 01. 2 DISASSEMBLY AND ASSEMBLY 8 - 1. Observe the following sequence of fixing screws. CAUTION: Attach the gears securely 1. Remove the parts as shown below, and remove the pressure release solenoid and the paper feed solenoid. AR- 5. 01. 2 DISASSEMBLY AND ASSEMBLY 8 - 1. Remove two screws and remove the fusing connector.